how to replace sink drain

Simply grip the stopper body and pull it out of the drain along with the hinged rocker arm. The kitchen sink strainer is tightly secured below the sink by a locking nut. Therefore, care should be taken when pushing, to avoid throwing the entire sink basin from the countertop. Disengage the connector ring from the tailpiece with your hands. Replace the basket strainer yourself in just an hour and save the cost of a visit from the plumber. Undo the screw holding the extension bar and lift out the drain stopper. Yvette Eddy started contributing to Nestlods.com in the summer of 2019. Install the Garbage Disposal and Strainer Install the garbage disposal onto the desired side of the sink first, since this takes up the most space. Loosen the locknut that holds the drain in place. Use a … Otherwise, continue to the section on removing the drain. A bathroom sink pop-up stopper is a very convenient feature, and while the installation is usually easy, occasionally the process is complicated due to variations in the fixture or fittings. The beveled side of the washer should be facing downward. Thanks to all authors for creating a page that has been read 129,558 times. The threads lock with corresponding threads fitted on the drain strainer. Your email address will not be published. In this article, we provide a precise and straightforward guide on how to replace the kitchen sink drain. PVC P-traps give you this small amount of wiggle room — if you have a metal P-trap, your replacement sink stopper assembly needs to be essentially the exact same length as the old one in order to avoid P-trap adjustments. Using a ring connector, secure the drain pipes to the protruding end of the tailpiece. If it's too long, you'll need to use a hacksaw or pipe cutter to trim off some of the pipe at some point — either at the top or bottom of the P-trap, or perhaps even a bit off the bottom of the sink stopper tailpipe itself. Lift the sink and drop it down into the opening. Use one hand to hold the stopper at the height you want it. How to Use Kitchen Knives Safely: Follow Some Steps, How To Replace Kitchen Sink Drain – 8 Easy Steps. James Schuelke, along with his twin brother David, is the co-owner of the Twin Home Experts, a licensed plumbing, leak detection, and mold inspection company based in Los Angeles, California. Slide the trap bend onto the sink tailpiece, and position it so the opposite side accepts the curved end of the waste arm. To prepare the new basket strainer’s surface, the putty is scraped off with a putty knife. (Warm the putty up with your hands first to make it easier to use – Be sure the Plumbers Putty is in a continuous circle) ", of myself! Quick and easy fix for a leaky kitchen sink basket strainer. By signing up you are agreeing to receive emails according to our privacy policy. Insert the Long Nose Pliers into the Sink Strainer to keep it from turning while loosening the Nut on the underside of Sink Drain. The Spruce / Aaron Stickley A leak under the kitchen sink could indicate that you need to replace the sink strainer. References. If you can find a new sink stopper set that matches your old one (and thus fits into your existing drain), you may be able to keep the existing sink drain in place. Sealing the drain is a fairly easy part of the overall sink installation process. You can make use this same mechanism later if you need to adjust your sink stopper: Look under the sink for a U-shaped clip with a bar that goes inside of the tailpiece. Install a basket strainer onto the sink basin without the garbage disposal. How to Repair & Replace the Drain Pipes on a Bathroom Sink. Your email address will not be published. Use a silicone caulk to seal the sink. When replacing a trap, you can use the same material as the old trap or choose something different. If your sink drain kit has a metal tailpipe, the exposed threads may be on the tailpipe instead of the sink drain. Don’t force or jerk the drainpipe or you could break it. With the bucket in place to catch any standing water, twist the slip nuts to the left to loosen them and remove the drain trap. Once the oil has seeped through, use an adjustable wrench to unfasten it. Sink drain traps are commonly made of white PVC, black ABS plastic, or chromed metal (brass or copper). A large hole or network of cracks may require a full sink replacement, but you can repair small holes as follows: Stainless steel sink: Sand the surface around the hole and wipe with an ammonia-based cleaner. Your first instinct may be to call a plumber, but you can save some money and earn some satisfaction by replacing the sink stopper yourself. Removing the Stopper, Lift Handle, and Connectors, {"smallUrl":"https:\/\/www.wikihow.com\/images\/thumb\/a\/a7\/Replace-a-Sink-Stopper-Step-1.jpg\/v4-460px-Replace-a-Sink-Stopper-Step-1.jpg","bigUrl":"\/images\/thumb\/a\/a7\/Replace-a-Sink-Stopper-Step-1.jpg\/aid9621969-v4-728px-Replace-a-Sink-Stopper-Step-1.jpg","smallWidth":460,"smallHeight":345,"bigWidth":728,"bigHeight":546,"licensing":"